Get Your Tripped Breaker Repaired By Trusted Electricians in Charleston

Get Your Tripped Breaker Repair in Charleston, SC

Tripped Breaker Repair In Charleston.

Tripped breakers occur when there’s an electrical fault that could damage the wires. Breakers don’t last forever and need to be replaced when they’re faulty. It’s all about protecting the wires at all cost!

When breakers trip, you’ll typically have to go to the garage or laundry room to reset the breaker. Sometimes, the breaker will automatically keep tripping. Circuit breakers are designed to protect the wires at all cost. You want the breaker to trip if there’s an issue or fault with the wiring. This isn’t something that a DIY should perform and its always best to hire a licensed and insured electrician in Charleston.

There are various reasons why you might have tripped breakers. It’s best to call us as we replace tripped breakers in Charleston, SC and surrounding areas!

Circuit overload

When the power is in extreme proportion, the panel will typically handle the power overload. However, if it keeps going on for more time, the breaker will automatically trip. It is not the circuit breaker’s fault, but it is the fault of the power.  See why we’re highly rated for tripped Breaker Replaced In Charleston.

There might be various reasons for this. If the electrical panel you use is less than 200 amps and the power consumption requires more, you will face this situation.

Let’s get a bit technical. There is a fixed amount of current set in the circuit. If the power exceeds the limit, it will be overloaded. That situation is where the circuit overload happens. Usually, the panel can easily handle it for a while. However, if it exceeds the limit of the breaker, it will trip the breaker, so the wires don’t burn up and cause a severe fire.

The excessive current is usually due to more current from the circuit being overloaded with too much power being used.
When the circuit is broken, the power will stop flowing. 

This is when the breaker will trip. This is one of the most common reasons for tripped breakers. However, there could be other reasons too.

Check out our electrical safety page here.

A Short Circuit

Many people have misconceptions thinking both of these are the same thing. However, a short circuit and circuit overload are two different things.

If you look at the definition, both of them might look a lot similar. A short circuit is where the circuit is literally shorter and never makes it to the load. The hot and neutral wires touch, causing a massive spike in amperage and ultimately tripping the breaker. 

A short circuit might also harm other devices and appliances. Therefore, the breaker is tripped to prevent you from other failures and hazards including being shocked or overheating and burning the wires.

Call us TODAY for tripped Breaker Repair in Charleston, SC

 

Tripped Breaker In Charleston

Tripped Breaker Issue Due to Ground Fault

Another reason for the tripped breakers is the ground fault. Whenever there is any inadvertent contact between the ungrounded or hot conductor and the grounding or bare copper wire, it will cause the ground fault. The normal return path of the current changes through the grounding system. This is why you see the breakers are tripping. The most common reasons for ground fault are because of the faulty wires or improper wiring. 

Whenever the ground fault happens, we will need to check the wires and also need to make sure that the ground and the conductor is no longer in contact. Typically wires become loose over time, especially if they’re improperly terminated to begin with.

Please never attempt to do complex electrical repair yourself.

 

Now, the main question arises. How can you know which is the reason for tripped breakers in your case?

Well, there is no particular way to find out that. You can try checking the wires and look for circuit errors. However, you will need basic knowledge about the circuit to do it. 

If not, you will end up spoiling more. Therefore, if you are not aware of anything, we recommend you not to do anything by yourself. In this way, your circuit can be safe.

You can call a professional and have it inspected. Once they inspect it, they will tell you the exact reasons why this is happening and what is the reason for the same.

The #1 reason why we don’t recommend you to do it by yourself is because of the other issues. There could be more than one problem that is causing the issue. Even if you put in some effort and can fix one, the breaker might still keep tripping.

This is much better than just doing it all by yourself. It’s also recommended that you check the panel regularly. The professionals can do it for you at an affordable cost. Either way, you can always request a free consultancy if you want help. You can talk to them and share the situation. Thereafter, you can decide whether you want to repair or upgrade.

If you have any issues regarding tripper breaker then contact us. We offer the best tripped breaker repair service in CharlestonSummerville, Bonneau & Ridgeville, SC regions.

 

LET’S GET YOU FREE PRICING

Transparent pricing is a right, not a luxury. We proudly offer free estimates on everything we do—just fill out our form to get started.

 

Recent Post

Related Post

search previous next tag category expand menu location phone mail time cart zoom edit close